Name them. Bosch does this with some functions too. I bought the model below and didn’t care about delayed start or whatever. I am not loading your app!
I swear we need to start some appliance hacking clubs or something to sidestep this crap.
Or haven’t paid your monthly bribe.
deck chair rearranging
How apropos.
Peep Show is hilarious, but I would be loathe to call it “charming”. It’s mostly a “guy show” I think.
Kim’s Convenience
Schitt’s Creek
.30-06 any better?
I’ll be sure to tell the family members I don’t talk to anymore about this…ug.
No, I would search for your motherboard model and forums to see what situations might match yours so that you might glean something useful as far as settings go. A quick check revealed nothing useful that stands out to me. Resetting all electrical connections was the lone useful tip. (The reddit link blocked me, lol. Fine) Perhaps more detailed (or different) search terms would produce better results.
I think you’ve taken the right steps to this point. Another CPU to test with would prove useful (though your original should suffice). Or another board to test this CPU in. Perhaps the shop you procured this one from has one or the other? Otherwise, I would pursue replacement.
What motherboard? What cpu did you have? Is this new Ryzen 5600 on the hardware list for the motherboard? If so, are there any voltage, stepping or other settings (listed in the manual) required to make it run stably?
Make sure the new cpu is clean with no potential shorts from anything. Also ensure good heatsink contact. If you’ve done all the normal and necessary steps then yes it might be a bad cpu, but they aren’t frequent failure items in my experience. Disagreeable conditions for the cpu is more commonly the culprit. Engineering sample cpus are the most fickle, but even some normal batch cpus might sometimes require a bit more (or less) juice or a system tweak.
Drive a screw into it. This is far easier to do with a carpeted floor since the screw head (and hole) is not as noticeable. Be aware not to have any screw heads sticking up anywhere when done. They do also make special screws that will snap the head off once sunk. Thus leaving no major visible trace, but you could use normal screws as long as you got them flush.
Try sinking the screw down on or near a squeaky spot in an attempt to tighten it up. You’ll need that screw to hit a floor joist as well to have something for the floor surface to tighten to. Sink one screw and test. If it didn’t help, back it out and try elsewhere nearby. It helps if you can identify the joist pattern for your floor.
You could also try from below the floor assuming access was available. But in that case, I’d also use caulk/glue from there too to help quite things down.
I would not do anything from above for a finished wood floor. Too easy to mess it up and your landlord would charge you for the damage. It is potentially do-able with finish nails, skill and careful precision (which I lack).
I keep seeing librewolf mentioned, so I’ve begun making the switch.
Is it possible to copy a profile over so sessions/tabs continue? Just curious. I am a tab hoarder.
DDG uses Bing primarily.
I have had reasonable experiences with startpage as a search engine.
On the scale of who is fucking up the world more, I’d have to award the trophy to Leon. Certainly fuck Nestle, but won’t someone please rid us of this meddlesome billionaire?
My family and friends are all shocked by my skills as an electrician.
Yes, I noticed that. It was the only donation link I spotted though. You could ask the admins that are listed in the right-side panel (TheDude, etc).
For yours, there is a heart outline up at the top of the page which leads to:
Well, that rule has been mostly tongue in cheek as you are probably aware, but perhaps Usenet will once again become useful to more folks. I have never veered away from it since I discovered it in the late 90’s. I suppose that makes me a part of the ES group? I’m quite glad to have discovered it. You do now have to pay to use it, but the cost is mild and the tools are all modernized with plenty of web front-ends out there.
Edited: Booboos
Hello fellow home labber! I have a home built xpenology box, proxmox server with a dozen vm’s, a hackentosh, and a workstation with 44 cores running linux. Oh, and a usb floppy drive. We are out here.
I also like long walks in Oblivion.